Important Plumber Guide for Installing a Bathtub
Important Plumber Guide for Installing a Bathtub
Blog Article
Were you in search of details on How to Install a Bathtub Yourself?
Setting up a tub isn't specifically brain surgery, but it does call for solid plumbing, woodworking, and also in some cases, tiling skills. Changing an old bathtub with a new one is likewise a moderately challenging project. If the old bathtub is readily easily accessible, the task can relocate easily; if you need to open up a wall surface to remove the old tub and also place the new tub, the task is much harder. In either instance, the task is within a residence handyman's skills, although you will need a helper to move out the old bathtub as well as embeded in the new one. Make sure you have actually certified yourself for the job as well as fit trying it. As opposed to working with a professional to take control of a halfway-completed project, it is far better to think about utilizing one before you start. Chances are you might require a professional plumber to make tube links.
This post will assist you install a new bathtub in your shower room if you have actually already gotten a brand-new tub and don't need to change the arrangement of your previous water supply pipes.
Your devices and also material list should make up the following:
Removing Old Taps
If you need to change old faucets with new ones as a part of your installment, after that the first thing you must do is detach the supply of water. After doing so, turn on the taps to drain any water remaining in the system. The process of getting rid of the existing taps can be fairly troublesome because of the limited access that is usually the situation.
Utilize a container wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipelines to the taps. Have a cloth prepared for the continuing to be water that will certainly originate from the pipelines. Once the supply pipes have been eliminated, utilize the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to quit the solitary taps from transforming throughout this procedure. Once the faucets have been removed, the holes in the bath/basin will certainly have to be cleaned of any old sealing substance.
Before going on to fit the new taps, compare the pipeline connections on the old taps to the brand-new faucets. If the old taps are longer than the brand-new faucets, after that a shank adapter is required for the brand-new taps to fit.
Fitting New Taps
If the tails of the brand-new taps are plastic, after that you will require a plastic connector to prevent damages to the thread. One end of the port fits on the plastic tail of the tap and the various other end gives a connection to the current supply pipes.
If you require to fit a monobloc, then you will need decreasing couplers, which links the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next off, place the tap in the installing hole in the bath/basin ensuring that the washers are in location in between the tap as well as the sink. Safeguard the faucet in position with the maker supplied backnut. Once the faucet is safely in place, the supply pipelines can be linked to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with normal tap connectors. The previous kind needs to be attached to the faucet finishes initially, tightening only by hand. The supply pipelines can later on be attached to the various other end. Tighten both ends with a spanner after both ends have actually been attached.
Mounting the Bath tub
Utilizing both wood boards under its feet, position the bath tub in the needed setting. The wood boards are helpful in uniformly spreading out the weight of the tub over the area of the boards rather than focusing all the weight onto 4 little factors.
The next goal is to make sure that the bathtub is leveled all round. This can be attained by inspecting the level and also readjusting the feet on the tub up until the level reads level.
To install taps, fit all-time low of the outermost versatile faucet connector to the suitable supply pipeline by making a compression join; after that do the very same for the other faucet.
Activate the water as well as check all joints and also brand-new pipework for leaks and also tighten them if required. Fill the bathtub as well as also examine the overflow electrical outlet and also the regular outlet for leakages.
Ultimately, take care of the bathroom paneling as described in the maker's user's manual. Tiling and also sealing around the bath tub ought to wait until the bath tub has actually been made use of at least once as this will settle it into its last setting.
Getting ready for the Installation
To start with, the sustaining structure supplied with the bathroom needs to be fitted (if needed) according to the manufacturer's directions. Next off, fit the taps or mixer to the bathtub. When suitable the tap block, it is essential to make certain that if the faucet features a plastic washer, it is fitted between the bathroom and also the faucets. On a plastic bath, it is also practical to fit a sustaining plate under the faucets unit to stop pressure on the tub.
Fit the flexible faucet connectors to the bottom of both taps using 2 nuts as well as olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet through the hole in the bath. Use the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bath. Make certain you use all of the provided washing machines.
Attach the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom should currently prepare to be fitted in its final position.
Tiling Around the Bathtub
In the location where the bath satisfies the ceramic tile, it is needed to secure the joins with a silicone rubber caulking. This is important as the installation can relocate enough to crack an inflexible seal, causing the water to permeate the wall surface between the bathroom as well as the tiling, bring about problems with dampness as well as feasible leaks to the ceiling listed below.
You can select from a variety of coloured sealers to assimilate your fixtures as well as fittings. They are sold in tubes as well as cartridges, and also can securing spaces as much as a width of 3mm (1/8 inch). If you have a larger space to load, you can fill it with spins of drenched paper or soft rope. Remember to constantly fill the bath tub with water before securing, to allow for the activity experienced when the bathtub is in use. The sealer can crack relatively early if you do not think about this motion before securing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also conveniently offered on the marketplace. It is suggested to fit the ceramic tiles making use of waterproof or water resistant adhesive and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We were shown that editorial on How to Install a Bathtub from an acquaintance on another domain. So long as you appreciated our blog entry kindly do not forget to pass it around. Many thanks for your time spent reading it.
Avoid property damage; contact us. Report this page